MAKING STRIATIONS IN A SOLID CYLINDER
how do i make striations in a solid cylinder? I know it should be possible but some how cannot figure out how?
View ArticleHow to enter the temperature that varies with time??
Due to the variation in air velocity, the external temperature varies with time. Can I know how can I input the values using an equation or an excel sheet??
View ArticleUnphysical solution with ellipsoid/sphere vs. hemisphere
Having a problem with COMSOL providing unphysical solutions when I use a sphere or ellipsoid "hovering" above the bottom of a domain as opposed to a hemisphere. I have a box, and within the box is a...
View Articlevoltage at different coordinates
Hello every one. it is possible in COMSOL to fine the voltage at (x,y,z) coordinates? thank you
View ArticleUndefined value found.
I am using poroelasticity module to simulate soil behavior of porous materials, the error information is as follows: Undefined value found. - Detail: Undefined value found in the stiffness matrix....
View ArticleCOMSOL Error Message
Hi I've been problems with COMSOL in Plasma Module The following feature has encountered a problem:"The source selection for the operator intpot1 must be nonempty. Error in multiphysics compilation. -...
View ArticleWhy COMSOL still requires the Young's modulus and Poisson ratio when defining...
Hi all, I want to play with Comsol for 3D simulations of linear elastic material. The materials are anisotropic so that I define elasticity matrices for them. But Comsol still requires me to give...
View ArticleHow to use Laminar Flow Pressure results in Solid Mechanics, help?
Hi, I need to use as an input in the Solid Mecanic module the Pressure results from Laminar Flow calculations. Can anyone explain me how to do this? thank you for yor answer. Best regards, Leonardo.
View ArticlePostprocessing in cyclindrical coordinates
I am doing a plane strain analysis of a pipe with a crack in it. I would like to get the stress components in the cyclindridcal coordinate system (radial, hoop stress) rather than in the cartesian...
View ArticleParticle Data Extraction
Hi there, I made a simulation of an electro-kinetic flow within a 2-phase medium, and after computing the currents I wanted to see how particles would behave within the geometry and the resulting...
View ArticleHow to solve the problem"Attempt to evaluate non-integral power of negative...
Hello, I am solving a Drift diffusion model for plasma using general form PDE. However, I am facing the following error, Failed to find consistent initial values. Attempt to evaluate non-integral power...
View ArticlePressure in Reacting Flow in Porous Media
Hello All, I am running a model in 4.3a with the node "Reacting Flow in Porous Media," and simulating groundwater flow in a confined aquifer. When I look at the results, my average pressure gets down...
View ArticleCloth or flag modeling
Hi all, Does anybody have a COMSOL model that simulates a cloth on a table or a flag moving under a wind flow? Cheers, SL
View ArticleParallel computing MatLab Comsol
Hi, I am using Comsol 4.3 with Livelink for Matlab. I run an optimization code in Matlab where i call Comsol to perform frequency response simulations. Now i would like to start two parallel frequency...
View ArticleAutomatic remeshing depending upon the gradient of the solution
Hello, everyone, I am solving a nonlinear equation on the plane. Its solution, u=u(x,y) is everywhere close to zero except for some region in the vicinity of the coordinate origin. This region is not...
View ArticleHow to determine face numbers (using matlab livelink) associated with an object
Hello again, I am trying to 'automatically' set my boundary conditions for a model generated in matlab with livelink. I know which objects need to have which boundary conditions based on a draw order...
View ArticleParameterise the position in a text file?
Hello, I want to use the 2D distribution of the relative permeability of a nonlinear calculation in a linear calculation of the same Model with same parameters etc. For that I export the data of the...
View ArticleContinuing Modeling Issues with 2D & 3D piezoelectric SAW model
Hello all, I’m in desperate need of help with my model. The initial model setup is a 2D cross-sectional SAW device where I have silicon, a metallic electrode as my ground, a buffer layer, a...
View ArticleProblem with 3D PDE thin layer mesh
Hi everyone I encountered a problem with meshing a thin layer(~10e-6m) with 3D PDE model. I am not sure how to mesh such thin layer. Has anyone managed to mesh a similar case? Looking forward to your...
View ArticleEigenfrequency seems right, but displacement units are totally wrong.
Dear Comsol Community, in the model attached I have a 20 micron long beam using the Solid Mechanics module to get the Eigenfrequencies. I calculated them manually using Euler-Beam theory and the first...
View Article